How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
Have you been looking for information and facts around How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, however it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also position the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Ensure you have qualified yourself for the job as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will assist you install a new bath tub in your shower room if you have actually already purchased a new bathtub and also don't require to alter the plan of your previous water supply pipelines.
Your devices as well as material list ought to comprise the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipelines. When the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub up until the level checks out degree.
To mount faucets, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and check all joints as well as new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the bath tub should wait until the bathtub has been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Setup
Firstly, the sustaining structure provided with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very curious about How to Install a Bathtub and I am assuming you appreciated our article. If you enjoyed our blog posting plz be sure to share it. I praise you for your time. Come back soon.
Visit Link
Report this page